89 revised: november 1, 2010 05:04 pm ?2010 littelfuse, inc teccor ? brand thyristors specifcations are subject to change without notice. please refer to http://www.littelfuse.com for current information. 10 amp standard & alternistor (high communitation) triacs qxx10xx & qxx10xhx series qxx10xx & qxx10xhx series main features description 10 amp bi-directional solid state switch series is designed for ac switching and phase control applications such as motor speed and temperature modulation controls, lighting controls, and static switching relays. standard type devices normally operate in quadrants i & iii triggered from ac line. symbol value unit i t(rms) 10 a v drm /v rrm 400 to 1000 v i gt (q1) 25 to 50 ma features & benefts ? rohs compliant ? glass C passivated junctions ? voltage capability up to 1000 v ? surge capability up to 120 a ? electrically isolated package l - package and ul recognized for 2500vrms ? solid-state switching eliminates arcing or contact bounce that create voltage transients ? no contacts to wear out from reaction of switching events ? restricted (or limited) rfi generation, depending on activation point sine wave applications alternistor type devices are used in applications requiring high commutation performance such as controlling inductive loads. isolated packages are offered with internal construction, having the case or mounting tab electrically isolated from the semiconductor chip. schematic symbol mt2 mt1 g agency approval agency agency file number ? l package: e71639 ?
90 revised: november 1, 2010 05:04 pm ?2010 littelfuse, inc teccor ? brand thyristors specifcations are subject to change without notice. please refer to http://www.littelfuse.com for current information. 10 amp standard & alternistor (high communitation) triacs qxx10xx & qxx10xhx series absolute maximum ratings standard triac symbol parameter value unit i t(rms) rms on-state current (full sine wave) qxx10ry/ qxx10ny t c = 95c 10 a qxx10ly t c = 90c i tsm non repetitive surge peak on-state current (full cycle, t j initial = 25c) f = 50 hz t = 20 ms 100 a f = 60 hz t = 16.7 ms 120 i 2 t i 2 t value for fusing t p = 8.3 ms 60 a 2 s di/dt critical rate of rise of on-state current i g = 200ma with 0.1s rise time f = 120 hz t j = 125c 70 a/s i gtm peak gate trigger current t p 10 s i gt i gtm t j = 125c 1. 8 a p g(av) average gate power dissipation t j = 125c 0.5 w t stg storage temperature range -40 to 150 c t j operating junction temperature range -40 to 125 c absolute maximum ratings alternistor triac (3 quadrants) symbol parameter value unit i t(rms) rms on-state current (full sine wave) qxx10lhy t c = 90c 10 a qxx10rhy/ qxx10nhy t c = 95c i tsm non repetitive surge peak on-state current (full cycle, t j initial = 25c) f = 50 hz t = 20 ms 110 a f = 60 hz t = 16.7 ms 120 i 2 t i 2 t value for fusing t p = 8.3 ms 60 a 2 s di/dt critical rate of rise of on-state current f = 120 hz t j = 125c 70 a/s i gtm peak gate trigger current t p 10 s i gt i gtm t j = 125c 2.0 a p g(av) average gate power dissipation t j = 125c 0.5 w t stg storage temperature range -40 to 150 c t j operating junction temperature range -40 to 125 c electrical characteristics (t j = 25c, unless otherwise specifed) standard triac symbol test conditions quadrant qxx10x4 qxx10x5 unit i gt v d = 12v r l = 60 i C ii C iii iv max. 25 50 50 75 (typ) ma v gt i C ii C iii max. 1. 3 v v gd v d = v drm r l = 3.3 k t j = 125c all min. 0.2 v i h i t = 200ma max. 35 50 ma dv/dt v d = v drm gate open t j = 125c 400v min. 150 225 v/s 600v 100 200 800v 75 175 v d = v drm gate open t j = 100c 1000v 50 150 (dv/dt)c (di/dt)c = 5.4 a/ms t j = 125c typ. 2 4 v/s t gt i g = 2 x igt pw = 15s i t = 14.1 a(pk) typ. 3.0 3.0 s note: xx = voltage, x = package, y = sensitivity
91 revised: november 1, 2010 05:04 pm ?2010 littelfuse, inc teccor ? brand thyristors specifcations are subject to change without notice. please refer to http://www.littelfuse.com for current information. 10 amp standard & alternistor (high communitation) triacs qxx10xx & qxx10xhx series electrical characteristics (t j = 25c, unless otherwise specifed) alternistor triac (3 quadrants) symbol test conditions quadrant value unit i gt v d = 12v r l = 60 i C ii C iii max. 50 ma v gt i C ii C iii max. 1. 3 v v gd v d = v drm r l = 3.3 k t j = 125c i C ii C iii min. 0.2 v i h i t = 100ma max. 50 ma dv/dt v d = v drm gate open t j = 125c 400v min. 750 v/s 600v 650 800v 500 v d = v drm gate open t j = 100c 1000v 300 (dv/dt)c (di/dt)c = 5.4 a/ms t j = 125c typ. 30 v/s t gt i g = 2 x igt pw = 15s i t = 14.1 a(pk) typ. 4.0 s static characteristics symbol test conditions value unit v tm i tm = 14.1a t p = 380 s max. 1.60 v i drm i rrm v drm = v rrm t j = 25c 400 - 600v max. 10 a t j = 125c 400 - 800v 2 ma t j = 100c 1000v 3 thermal resistances symbol parameter value unit r (j-c) junction to case (ac) qxx10ryy/ qxx10nyy 1. 3 c/w qxx10lyy 2.6 r (j-a) junction to ambient (ac) qxx10ryy 45 c/w qxx10lyy 50 note: xx = voltage, x = package, y = sensitivity, yy = type & sensitivity
92 revised: november 1, 2010 05:04 pm ?2010 littelfuse, inc teccor ? brand thyristors specifcations are subject to change without notice. please refer to http://www.littelfuse.com for current information. 10 amp standard & alternistor (high communitation) triacs qxx10xx & qxx10xhx series figure 2: normalized dc gate trigger current for all quadrants vs. junction temperature +125 0.0 1.0 2.0 3.0 4.0 -65 -40 -15 10 35 60 85 110 junction temperature (t j ) - oc ratio of i gt / i gt (t j = 25oc) mt2 positive (p ositi ve half cycle) mt2 ne ga tive (neg ati ve half cycle) mt1 mt2 + i gt ref qii mt1 i gt ga te mt2 ref mt1 mt2 ref mt1 mt2 ref qi qiv qiii all polarities are referenced to mt1 ( - ) i gt ga te (+) i gt - i gt ga te ( - ) i gt ga te (+) + - figure 1: defnition of quadrants note: alternistors will not operate in qiv 0 2 4 6 8 10 12 0 2 4 6 8 10 12 rms on-state current [i t(rms) ] - amps average on-state power dissipation o [p d (av) ] - watts current waveform: sinusoidal load: resistive or inductive conduction angle: 360 figure 5: power dissipation (typical) vs. rms on-state current figure 6: maximum allowable case temperature vs. on-state current qx x 10r yy qx x 10n yy q xx1 0lyy 60 70 80 90 100 110 120 130 0 2 4 6 8 10 12 14 ma x allo wa bl e c ase te mp er at ur e (t c ) - c rms on-stat e cur r ent [i t(rms) ] - amps figure 3: normalized dc holding current vs. junction temperature figure 4: normalized dc gate trigger voltage for all quadrants vs. junction temperature +125 0.0 1.0 2.0 3.0 4.0 -65 -40 -15 10 35 60 85 110 junction temperature (t j ) - oc ratio of i h / i h (t j = 25oc) +125 0.0 0.5 1.0 1.5 2.0 -65 -40 -15 10 35 60 85 110 junction temperature (t j ) - oc ratio of v gt / v gt (t j = 25oc)
93 revised: november 1, 2010 05:04 pm ?2010 littelfuse, inc teccor ? brand thyristors specifcations are subject to change without notice. please refer to http://www.littelfuse.com for current information. 10 amp standard & alternistor (high communitation) triacs qxx10xx & qxx10xhx series figure 7: maximum allowable ambient temperature vs. on-state current figure 8: on-state current vs. on-state voltage (typical) t c = 25 oc 0 2 4 6 8 10 12 14 16 18 20 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 positive or negative instantaneous on-state voltage (v t ) - volts positive or negative instantaneous on-state current (i t ) - amps qxx10ly qxx10ry qxx10lhy qxx10rhy 20 30 40 50 60 70 80 90 100 110 120 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 rms on-state current [i t(rms) ] - amps max allowable ambient temperature current waveform: sinusoidal load: resistive or inductive conduction angle: 360o free air rating - no heatsink (t a ) - oc figure 9: surge peak on-state current vs. number of cycles 1 10 100 1000 1000 100 10 1 surge current duration - full cycles peak surge (non-repetitive) on-state current (i tsm ) - amps supply frequency: 60 hz sinusoidal load: resistive rms on-state current: [i t(rms) ]: maximum rated value at specifed case temperature notes: 1. gate control may be lost during and immediately following surge current interval. 2. overload may not be repeated until junction temperature has returned to steady-state rated value.
94 revised: november 1, 2010 05:04 pm ?2010 littelfuse, inc teccor ? brand thyristors specifcations are subject to change without notice. please refer to http://www.littelfuse.com for current information. 10 amp standard & alternistor (high communitation) triacs qxx10xx & qxx10xhx series soldering parameters refow condition pb C free assembly pre heat - temperature min (t s(min) ) 150c - temperature max (t s(max) ) 200c - time (min to max) (t s ) 60 C 180 secs average ramp up rate (liquidus temp) (t l ) to peak 5c/second max t s(max) to t l - ramp-up rate 5c/second max refow - temperature (t l ) (liquidus) 217c - temperature (t l ) 60 C 150 seconds peak temperature (t p ) 260 +0/-5 c time within 5c of actual peak temperature (t p ) 20 C 40 seconds ramp-down rate 5c/second max time 25c to peak temperature (t p ) 8 minutes max. do not exceed 280c physical specifcations environmental specifcations test specifcations and conditions ac blocking mil-std-750, m-1040, cond a applied peak ac voltage @ 125c for 1008 hours temperature cycling mil-std-750, m-1051, 100 cycles; -40c to +150c, 15-min dwell-time temperature/ humidity eia/jedec, jesd22-a101 1008 hours; 320v - dc: 85c; 85% rel humidity high temp storage mil-std-750, m-1031, 1008 hours; 150c low-temp storage 1008 hours; -40c thermal shock mil-std-750, m-1056 10 cycles; 0c to 100c; 5-min dwell time at each temperature; 10 sec (max) transfer time between temperature autoclave eia/jedec, jesd22-a102 168 hours (121c at 2 atms) and 100% r/h resistance to solder heat mil-std-750 method 2031 solderability ansi/j-std-002, category 3 test a lead bend mil-std-750, m-2036 cond e terminal finish 100% matte tin-plated body material ul recognized epoxy meeting fammabilty classifcation 94v-0. terminal material copper alloy design considerations careful selection of the correct device for the applications operating parameters and environment will go a long way toward extending the operating life of the thyristor. good design practice should limit the maximum continuous current through the main terminals to 75% of the device rating. other ways to ensure long life for a power discrete semiconductor are proper heat sinking and selection of voltage ratings for worst case conditions. overheating, overvoltage (including dv/dt), and surge currents are the main killers of semiconductors. correct mounting, soldering, and forming of the leads also help protect against component damage. ti me te mperature t p t l t s(max) t s(min) 25 t p t l t s time to peak temperature preheat p r e h eat ramp-up ramp-up ramp-down r am p - do
95 revised: november 1, 2010 05:04 pm ?2010 littelfuse, inc teccor ? brand thyristors specifcations are subject to change without notice. please refer to http://www.littelfuse.com for current information. 10 amp standard & alternistor (high communitation) triacs qxx10xx & qxx10xhx series dimensions to-220ab (r-package) non-isolated mounting tab common with center lead dimension inches millimeters min max min max a 0.380 0.420 9.65 10.67 b 0.105 0.115 2.67 2.92 c 0.230 0.250 5.84 6.35 d 0.590 0.620 14.99 15.75 e 0.142 0.147 3.61 3.73 f 0.110 0.130 2.79 3.30 g 0.540 0.575 13.72 14.61 h 0.025 0.035 0.64 0.89 j 0.195 0.205 4.95 5.21 k 0.095 0.105 2.41 2.67 l 0.060 0.075 1.52 1.91 m 0.085 0.095 2.16 2.41 n 0.018 0.024 0.46 0.61 o 0.178 0.188 4.52 4.78 p 0.045 0.060 1. 14 1.52 r 0.038 0.048 0.965 1.22 k j a h g b f ? e c d l r t c mea suring poin t mt2 mt2 o p n m mt1 .27 6 7. 01 .526 1 3.36 .320 8.1 3 ga te no tch in ga te lead to id. non-isola ted ta b area (ref .) 0.1 7 in 2 dimensions to-220ab (l-package) isolated mounting tab dimension inches millimeters min max min max a 0.380 0.420 9.65 10.67 b 0.105 0.115 2.67 2.92 c 0.230 0.250 5.84 6.35 d 0.590 0.620 14.99 15.75 e 0.142 0.147 3.61 3.73 f 0.110 0.130 2.79 3.30 g 0.540 0.575 13.72 14.61 h 0.025 0.035 0.64 0.89 j 0.195 0.205 4.95 5.21 k 0.095 0.105 2.41 2.67 l 0.060 0.075 1.52 1.91 m 0.085 0.095 2.16 2.41 n 0.018 0.024 0.46 0.61 o 0.178 0.188 4.52 4.78 p 0.045 0.060 1. 14 1.52 r 0.038 0.048 0.965 1.22 k j a h g b f ? e c d l r t c mea suring poin t mt2 o p n m mt1 ga te area (ref .) 0.1 7 in 2 .320 8.1 3 .526 1 3.36 .27 6 7. 01 note: maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 nm). note: maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 nm).
96 revised: november 1, 2010 05:04 pm ?2010 littelfuse, inc teccor ? brand thyristors specifcations are subject to change without notice. please refer to http://www.littelfuse.com for current information. 10 amp standard & alternistor (high communitation) triacs qxx10xx & qxx10xhx series dimensions to-263aa (n-package) d 2 -pak surface mount dimension inches millimeters min max min max a 0.360 0.370 9.14 9.40 b 0.380 0.420 9.65 10.67 c 0.178 0.188 4.52 4.78 d 0.025 0.035 0.64 0.89 e 0.045 0.060 1. 14 1.52 f 0.060 0.075 1.52 1.91 g 0.095 0.105 2.41 2.67 h 0.092 0.102 2.34 2.59 j 0.018 0.024 0.46 0.61 k 0.090 0.110 2.29 2.79 s 0.590 0.625 14.99 15.88 v 0.035 0.045 0.89 1. 14 u 0.002 0.010 0.05 0.25 w 0.040 0.070 1. 016 1.78 g b a w v s mt1 mt2 t c mea suring poin t c e k h j u .320 8.1 3 .27 6 7. 01 .331 8.41 ga te .460 11 .68 .665 1 6.89 .260 6.60 .1 50 3.81 .080 2.03 .085 2.1 6 .055 1 .40 .350 8.89 .27 6 7. 01 .27 6 7. 01 area: 0.1 1 in 2 d f product selector part number voltage (xx) gate sensitivity quadrants type package 400v 600v 800v 1000v i C ii C iii iv QXX10L4 x x x x 25 ma 50 ma standard triac to-220l qxx10r4 x x x x 25 ma 50 ma standard triac to-220r qxx10n4 x x x x 25 ma 50 ma standard triac to-263 d2-pak qxx10l5 x x x x 50 ma standard triac to-220l qxx10r5 x x x x 50 ma standard triac to-220r qxx10n5 x x x x 50 ma standard triac to-263 d2-pak qxx10lh5 x x x x 50 ma alternistor triac to-220l qxx10rh5 x x x x 50 ma alternistor triac to-220r qxx10nh5 x x x x 50 ma alternistor triac to-263 d2-pak packing options part number marking weight packing mode base quantity qxx10l/ryy qxx10l/ryy 2.2 g bulk 500 qxx10l/ryytp qxx10l/ryy 2.2 g tube pack 500 (50 per tube) qxx10nyytp qxx10nyy 1.6 g tube 500 (50 per tube) qxx10nyyrp qxx10nyy 1.6 g embossed carrier 500 note: xx = voltage, yy = type & sensitivity
97 revised: november 1, 2010 05:04 pm ?2010 littelfuse, inc teccor ? brand thyristors specifcations are subject to change without notice. please refer to http://www.littelfuse.com for current information. 10 amp standard & alternistor (high communitation) triacs qxx10xx & qxx10xhx series gate mt1 mt2 0.512 (13.0) arbor hole dia. 0.945 (24.0) 0.63 (16.0) 1.01 (25.7) 12.99 (330.0) 0.827 (21.0) 0.157 (4.0) direc tion of f eed dimensions are in inches (and millimeters). * * cov er tape 0.059 dia (1.5) to-263 embossed carrier reel pack (rp) specifcations meets all eia-481-2 standards part numbering system q 60 10 l h5 56 device type q: triac or alternisto r voltage ratin g 40: 400v 60: 600v 80: 800v k0: 1000v current rating 10: 10 a sensitivity standard triac: 4: 25 ma (qi, ii, iii) 50 ma (qiv ) 5: 50 ma (qi, ii, iii) alternistor triac: h5: 50ma (qi, ii, iii) package type l: to-220 isolated r: to-220 non-isolated n: to-263 (d 2 pak) lead form dimension s xx: lead form option part marking system to-202 type 1 (f package ) q6010 f5 1 y xxxx ? ? ? my m y q6010r 5 q6010l 5
|
